Guide · RV & motorhome · 5 min read

RV black tank sensor reads full? Why cleaning rarely lasts

If the panel shows 2/3 or full on an empty black tank, the sensor is not broken. It is coated. Here is how to clean it, why the problem comes back, and how to stop it for good.

Motorhome parked under pine trees

Why an empty tank reads full

Most RV holding tanks are measured by three or four metal probes screwed through the side wall at one third, two thirds and full. The monitor panel checks whether current can pass between two probes. If it can, it assumes liquid is there and lights the lamp.

In a black tank that test is easy to fool. Toilet paper, waste and grease dry onto the probes and form a film that conducts on its own, or a scrap of paper bridges two probes. The panel then reports 2/3 or full on a tank you have just emptied. On the grey tank, soap scum and cooking grease do the same.

So the sensor usually works. It is measuring the dirt on the probe, not the liquid in the tank.

If you want to try cleaning first

How to clean RV tank sensors

These are the methods RV owners use. They work, for a while.

Avoid bleach and strong solvents. They attack the seals in the valves and toilet, and they kill the bacteria that break the waste down.

  1. 01

    Rinse right after dumping

    Dump the black tank, then run the tank rinse or a flush wand through the toilet until the water runs clear. Close the valve and add a few litres of water, so solids never dry onto the walls.

  2. 02

    Soak and drive

    Fill the tank about a third with water and a sensor cleaner or enzyme treatment, and drive with it. The movement scrubs the walls and probes. Dump after a day or two. For the grey tank, dish soap and hot water loosen the grease.

  3. 03

    Try the ice trick

    Some owners add a bag of ice and water before a drive, so the ice scours the walls. It helps on loose deposits, not on a film baked onto the probes.

  4. 04

    Check the panel empty

    With the tank rinsed and empty, the panel should show E. If it still shows 1/3 or 2/3, a probe is still bridged or a connection behind the panel is corroded.

The catch

Why the reading comes back

Cleaning removes the film, but the probes are still inside the tank, sitting in the same waste. The build-up starts again on the first trip, and most owners are back to a stuck 2/3 within weeks or months.

Replacing the probes gives the same result, plus new holes in the tank to seal. And even a clean probe sensor only knows three or four heights. It can tell you a third or two thirds, not whether you have room for one more night.

The permanent fix

Measure from outside the tank

A sensor that never touches the waste cannot foul. There is nothing left to clean.

  • Gobius C sits on the top face of a plastic or fibreglass tank and reads the liquid surface with micro radar, through the wall. You get a continuous 0–100 %, accurate to 2 mm, with nothing drilled. Almost every RV tank is plastic, so this is the usual choice.
  • Gobius Pro glues to the side wall when the top of the tank cannot be reached. It reads through any material and gives an alarm at the height you choose, for example at 75 % on the black tank.
  • Capacitive strips glued to the side wall are another external option. See how they compare in Gobius vs SeeLevel.

All tanks show in the Gobius app over Bluetooth. The old probes can stay where they are, unplugged, and the tank stays sealed.

A Gobius C sensor mounted on top of a plastic tankThe Gobius app showing a water tank at 58 percent, 73 of 125 litres
Gobius C on the tank top, the level in the app

Sensors

Pick by how you reach the tank

Top of the tank reachable: Gobius C. Only the side: Gobius Pro. Not sure? Send us a photo of the tank and we will tell you what fits.

Gobius C, Basic, 0-100%

Plug and play installation. No disassembly of the tank is needed. Measures from the top, never risk of leakage. Complete system, everything included; sensor, 2 m cable, Quick Guide and a 3M cleaning wipe. Handles voltage of 12-24 Volts.…

Details

Gobius C, NMEA 2000, 0-100%

Plug and play installation. Can be connected direct to a NMEA 2000 networks. No disassembly of the tank is needed. Measures from the top, never risk of leakage. Complete system, everything included; sensor, NMEA 2000 cable, 3M cleaning…

Details

Sensor tape kit, Gobius and Gobius Pro

Useful for attaching Gobius and Gobius Pro sensors on the tank. Can't be used for Gobius C sensors.

Details

Gobius C, all analog outputs, 0-100%

Plug and play installation. No disassembly of the tank is needed. Measures from the top, never risk of leakage. Complete system, everything included; sensor, cable, 3M cleaning wipe. Handles voltage of 12-24 Volts. The sensor is mounted in…

Details

Gobius Pro with 1 sensor

Measuring from the outside the tank, nothing on the inside. Bluetooth and App for your phone included.

Details

Gobius Pro with 2 sensors

Measuring from the outside the tank, nothing on the inside. Bluetooth and App for your phone included.

Details

Gobius Pro with 3 sensors

Measuring from the outside the tank, nothing on the inside. Bluetooth and App for your phone included.

Details

Gobius 4 for grey, black & waste tanks

Complete tank monitor system for grey, black and waste tanks, version 5.0.

Details

Gobius 4 for water/fuel- & fluid tanks

Complete tank monitor system for water, fuel and other fluids.

Details

Upgrade Gobius 1 to Gobius 4, grey, black & waste tanks

For waste tanks

Details

Upgrade Gobius 1 to Gobius 4 for water/fuel- & fluid tanks

For water/fuel- & fluid tanks, version 5.0.

Details

Gobius panel cable, 1,5 m

Used to connect the panel to the Control unit.

Details

New Control unit for Gobius 1 and 4 for grey, black & waste tanks

Control unit for Gobius 1 and Gobius 4, Waste tanks, version 5.0.

Details

Upgrade your old Gobius to version 5.0

Step up to the version 5.0 of Gobius 4, Waste or Water/Fuel/Fluid.

Details

New Control unit for Gobius 1 and 4 for water/fuel- & fluid tanks

Control unit for water/fuel- & fluid tanks, version 5.0.

Details

NMEA 2000 Converter

Converts tank data from Gobius and Gobius Pro to NMEA 2000 networks.

Details

Gobius panel (PIR)

Smart overfill alarm panel with built-in motion sensor (PIR). Starts Gobius when you visit the toilet and switches off automatically after 60 seconds. Alarms when the waste tank is full. Only 12 Volt.

Details

Gobius panel for grey, black & waste tanks

For Gobius 1 and 4, grey, black & waste tanks.

Details

Gobius panel for water/fuel- and fluid tanks

For Gobius 1 and 4, for water/fuel- and fluid tanks.

Details

Hub for Gobius Pro sensors

Out signals: 10-180 Ohm and 240-33 Ohm. Read more about the Hub at Gobiuspro.com, Documentation.

Details

Audible alarm, buzzer

Suitable for all Gobius products, (version 3.0, 4.0 and 5.0) and also for Gobius Pro sensors.

Details
Campervan parked at a coastal overlook
Another night here, or the service point?
Gobius Pro sensor mounted on a tank wall next to the app showing the level
Gobius Pro on the side wall, when the top is out of reach

Questions

RV tank sensors: asked and answered

Why does my RV black tank sensor say full when the tank is empty?

Because the probes inside the tank are coated or bridged by paper, waste and grease. The panel reads a connection between two probes as liquid, so a dirty probe looks exactly like a full tank.

How do I clean RV tank sensors?

Rinse the tank right after dumping, then fill it about a third with water and a sensor cleaner or enzyme treatment and drive with it before dumping again. Avoid bleach and strong solvents, which attack seals and valves.

Expect the reading to drift back over time, because the probes stay in the waste.

Can I replace RV tank probes with a sensor outside the tank?

Yes. Gobius C sits on the top face of a plastic or fibreglass tank and reads through the wall, and Gobius Pro reads from the side through any material. Nothing is drilled and nothing touches the waste. The old probes can stay where they are, unplugged.

Does an external sensor work on the grey and fresh water tanks too?

Yes. The same sensor reads fresh, grey and black water, and all tanks show in one app on your phone.

Stop cleaning the sensor

Measure the black tank from outside and the reading stays right, trip after trip.