Support · FAQ
Questions & answers
Everything we get asked, in one place, grouped by theme. If yours isn’t here, ask us directly — and we’ll probably add it.
Choosing a sensor
Which sensor do I need — Gobius C or Gobius Pro?
Start from what you want to see. A stepless 0–100 % reading means Gobius C: micro radar on top of the tank, reading the surface below. A metal tank, or one fixed alarm point, means Gobius Pro: glued to the outside of the wall, reading through it with nothing drilled. Side by side here. If you have a hole on top of the metal tank, you can use Gobius C with our adapter for standard hole, 1 1/4″, SAE5 flange.
Does it work on a metal tank?
Gobius Pro does, from the outside: stainless and steel up to 3 mm, aluminium up to 5 mm. Gobius C is radar, and radar cannot pass through metal — on a metal tank it needs a small port fitted in the tank top. You should use our ?Adapter for 1 1/4” / SAE 5 flange.
Do I have to drill the tank?
Not on polyethelene or fiberglass: both sensors work from the outside, with the tank sealed and full. Metal is the one exception for Gobius C — radar cannot pass through it, so a metal tank needs a small port in the top. Gobius Pro reads metal from the side with nothing drilled. More in no-drill installations.
What liquids can Gobius measure?
Fresh water, grey water, black water, diesel, petrol and oil — the same sensors, C and Pro, for all of them. Nothing touches the liquid, so dirty or aggressive contents cause no wear, which is why holding tanks are such a common use.
Which versions are there?
Gobius Pro comes as a sensor kit, and you can add extra sensors for more levels or more tanks. Gobius C comes three ways: Basic drives a standard analog gauge (0–190 or 240–33 Ohm) as well as the app; Analog Outputs adds 4–20 mA and 0–5 V; NMEA 2000 puts your volumes on the boat network. All three Gobius C versions also connect over Bluetooth to Victron Cerbo GX and Roam Hub. For prices, ask your dealer or contact us.
Tanks and materials
How deep does my tank have to be?
Gobius C works from 200 mm to 4500 mm of depth. Below 200 mm there is not enough travel between full and empty for a meaningful percentage — on a shallow tank, one alarm point from Gobius Pro on the side wall is the more useful answer.
My tank floor slopes. Will the level be wrong?
No — this is what Gobius C is built for. It measures the true distance down to the surface, and the Tank Calculator turns that depth into real litres for a slanted, tapered or stepped tank. Where the sensor sits matters: over the deepest part, empty arrives when the tank really is empty; over the shallow end, early.
Is the Tank Calculator included with the sensor?
No. The Gobius Tank Calculator is a separate app, free to download at AppStore and Google Play — not a subscription, and not bundled with any sensor. It turns the level Gobius C measures into true litres or gallons for your tank’s exact shape, so it needs a Gobius C and does not work with Gobius Pro.
There is a baffle across my tank. Is that a problem?
Only if a sensor lands on it. Liquid finds its own level on both sides, so a Gobius C over a clear section reads the whole tank correctly; in the app’s Search mode a baffle shows up as a value that will not settle. Gobius Pro reads only its own patch of wall — keep it clear of the points where baffles attach, which stiffen the wall.
My tank is insulated. Does that rule it out?
Not necessarily, but check first. The sensor must sit against the tank itself: foam, lagging, cladding or a second outer wall will spoil the reading. If it can be cut back to expose a bare, flat area, you are usually fine. Send us a photo before you cut anything.
Fitting it
Where does each sensor need to sit?
Gobius C needs a horizontal flat spot about its own size on top of the tank, at least 35 mm from any edge, a clear view down, and at least 40 mm of air above the surface at full. Gobius Pro needs a flat, bare patch the size of your hand on a side wall, clear of welds, seams and corners, at the exact height you care about. More on limitations and placement.
How long does fitting take?
About 15 minutes per sensor on a normal tank, plus a short calibration in the app, and the tank can stay full and where it is. After that there is nothing to maintain: no moving parts, nothing inside the tank. Step-by-step instructions are in the installation guides.
Do I need to empty the tank first?
Not for Gobius Pro — mount it, then calibrate against known levels. Gobius C needs at least 150 mm of air between sensor and surface to calibrate, so a fairly empty tank is easiest.
Can I move a sensor later
All sensors are intended to be permanently attached, so plan their placement in advance; they can be difficult to remove. If you wish to change the position of Gobius Pro or Original sensor, you will need to order new 3M adhesive strips.
You can reattach Gobius C sensors using a thin strip of adhesive around the sensor—do not apply adhesive underneath the sensor.
PLEASE NOTE: You must always perform a new Calibration whenever you have moved a sensor.
Reading the level
How accurate is Gobius C?
2 mm resolution, updated more than once a second, steplessly from 0 to 100 %. Calibration maps the tank’s volume, so the percentage you see is a percentage of litres or gallons rather than of height — even in a V-shaped tank.
Why doesn’t Gobius Pro give me a percentage?
Because of what it measures. Each sensor reads whether liquid is behind the sensor spot on the wall — a yes or no at that height. Several sensors give you a more steps, but never the smooth, stepless number that radar gives. If you want an exact volume, choose Gobius C.
How can Gobius Pro read through a metal wall?
It ‘knock and listen’ at the tank wall and analyze the response: liquid behind the wall damps that vibration measurably, air does not. Patented in Sweden, the US and Europe — the longer version is on how it works.
Does sloshing under way ruin the reading?
No. Gobius C takes many readings and filters the motion out to find the true surface underneath, so the level stays calm even when the boat or vehicle are not. Gobius Pro is unaffected for another reason: each point simply reports fluid or not.
The volume looks wrong. What do I check first?
Redo the calibration, then check the placement and ensure that the tank depth value is correct. You can also use the search function in the Gobius C app. Are the values still incorrect? Verify that the sensor is firmly attached to a clean, dry, and horizontal surface. You are welcome to send a support email from within the app—see "Sensor Details."
App and connections
Which app do I use, and is it free?
The Gobius app is free on iOS and Android and available in 10 languages. It talks to the sensor over Bluetooth — no hub, no cloud, no account to create. The Tank Calculator is a separate app and is also free.
Can I get an alarm before the tank is full and empty?
Yes. Two alarm levels per tank in the app, at whatever percentages you choose. Gobius Pro can also switch a lamp, a buzzer or a pump directly, so it still warns you when no phone is aboard.
The app can’t find my sensor.
Stand next to the tank: Bluetooth is deliberately short range, and a metal locker or bulkhead blocks it. Check the app has Bluetooth permission in your phones settings— some Android versions ask for location too — turn Bluetooth off and on, and confirm the sensor has power at the fuse and connector.
Does it work with NMEA 2000, my chartplotter or Victron?
Yes, with the NMEA 2000 version of Gobius C. It sends standard fluid data, so Garmin, Raymarine, B&G, Simrad and Furuno plotters display it natively, and Victron GX and Roam Hub, devices show it via Bluetooth on screen and in VRM.
What power do the sensors need?
12–24 V DC, and very little of it — designed for boats and vehicles living on batteries. Gobius C is rated IP 66. The NMEA 2000 version powers straight from the network.
Warranty and support
What warranty do I get?
One year. Please register your product; phone and email support is free every working day, 9–17 CET.
Do I have to register to get support?
No, we will not leave anyone stranded. But registration is what makes support free and fast: your product, your tank and your history are in front of us before we pick up the phone. Second-hand units count too — the warranty runs from the original purchase.
How do I contact support about my sensor?
Send a support email from the Gobius app: open the sensor, go to Sensor Details and send it from there. Please use this route for any question about a sensor.
Gobius Original works without the app, so for that one, use the form on the Support page or the Contact page.
My old Gobius 4 — is it still supported?
Yes. Gobius 4 lives on as Gobius Original: same patented method, new name, one version for waste tanks and one for water and fuel. We still support earlier generations, and you can register them as an older Gobius model.
Want the level in your phone instead of on a panel? Then Gobius Pro or Gobius C is the step up, and it can reuse your mounting positions.
Ready to see the actual volume in your tank?
Order directly from us or find your nearest dealer. Installation takes about 15 minutes.