Support · sensor placement

Measurement rules

Gobius sensors read through the tank wall, so where you put them decides what you get. Gobius C sits on the tank top and measures straight down; Gobius Pro and Original glue to a side wall and report one and 4 levels. Very few tanks are plain boxes — here is what that means on the shapes we actually see.

✓ Gobius C · good placement

Irregular tanks, and where the sensor goes

Tanks are moulded to fit the space they live in. These are the shapes that turn up most often, and the spot that works on each.

Rectangular tank

The reference case. Centre of the tank top: a clear run down and the widest margin to every edge.

Note: keep at least 35 mm from any edge.

Cut corner at the top

Stay on the flat part of the top. The sensor needs a level patch to sit on.

Note: a flat mounting surface matters more than being central.

Cut corner at the bottom

Mount where the beam lands on the flat floor rather than on the slope.

Note: over the slope it reads the slope, not the level.

Stepped tank

Two depths, one reading. Sit over the deeper section so the level keeps falling all the way to empty.

Note: over the shallow step it calls empty while litres remain.

Sloping sides

A hull-shaped tank still has a flat strip down the middle of the floor. Aim at that.

Note: the centre line is usually the deepest part.

Baffles inside

Baffles are no problem, as long as the sensor looks into a clear bay between them.

Note: a baffle under the sensor gets measured instead of the liquid.

DLiquid

Pointed bottom

A tank that narrows to a point has no flat floor to reflect from. Fill it a little first, and the liquid itself gives you the flat surface to measure against.

Note: about 5 cm of liquid is enough to form a level surface.

Odd shape? Let the calculator do the litres

Placement gives you the level. The Gobius Tank Calculator turns that level into true litres for your exact tank shape — you fill in steps and it builds the profile. It is a separate app, and it needs a Gobius C.

✕ Gobius C · poor placement

Examples of poor placements

Three spots that will not give you a reading you can trust.

Beam onto a sloping floor

The sensor sits over the cut corner, so the beam lands on the slope. The reading drifts and empty arrives early.

Note: move it over the flat part of the floor.

Sensor on a sloping top

On the slope it points sideways instead of straight down, and measures the far wall.

Note: it has to sit level, looking straight down.

Too close to an edge or a pipe

One sensor is hard against the tank edge. The other sits beside a standpipe — beside is close enough, because the beam spreads as it goes down.

Note: keep 35 mm from edges, and clear of anything standing inside.

✓ Gobius Pro · good placement

Where a side-wall sensor works

Gobius Pro glues to the outside of a side wall and reports one fixed level. It needs bare, flat wall — and three sensors on one tank simply means three heights.

HIGHLOW
Different heights on one wall — one level each
LOWHIGH
Different sides of the same tank works fine
3.5 cm
Flat wall, 3.5 cm clear all round, nothing touching

One rule covers nearly all of it: bare flat wall, 3.5 cm clear all round, and nothing strapped, clamped or glued across the sensor.

✕ Gobius Pro · poor placement

Five ways to get the wall spot wrong

The five we see most often, drawn on the awkward tank shapes they actually happen on — tapered, saddle, stepped, V-bottomed.

3.5 cm
Too close to the edge — leave 3.5 cm of flat wall all round
PIPE
Wedged against a pipe — it needs free space, nothing touching
STRAP
Under a tie-down strap — the strap damps the wall
SEALANT
Never seal around a sensor — sealant ruins the measurement
SAME LEVEL
Two sensors at one height — give each sensor its own level

Not sure by eye

The app can check the spot before you commit

You do not have to work it out from drawings alone.

Hold the sensor where you are thinking of fitting it — on the tank top for Gobius C — and run Search in the Gobius app. It reads that exact spot and tells you whether it is a good placement. Move it a few centimeters and check again. It takes seconds, and it happens before you glue anything down.
Pro and Original have no Search function.

Gobius C sensor mounted on the flat top of a plastic water tank
Flat field between the ribs

Still not sure?

Send us a photo of the tank top and the rough dimensions. We look at tanks all day and will point you to the right one — or honestly say when it is a better fit for Gobius Pro or Gobius Original.

This page is the pictures.

The numbers live next door: tank depth, the clearance a full tank needs, and the wall thickness each material allows — everything that decides whether a tank is a yes, a no, or a job for Gobius Pro.