Guide · 6 min read

How to measure a black water tank

Every method for knowing what’s in the holding tank — from the screwdriver knock to radar through the wall — and the setup that actually works for years.

Why this tank is the hard one

The black water tank is the one tank you cannot look into, cannot dip, and really cannot afford to overfill. It is also the tank where every conventional indicators dies: floats jam in tissue, capacitive probes coat over, and each extra fitting in the wall becomes a permanent odour path. So the measurement problem is really a constraint problem: how do you read the level without anything touching the contents?

The methods, worst to best

The knock test

Tap the tank with a screwdriver handle and listen for the pitch change at the liquid line. Free, and genuinely how most crews do it — when the tank is reachable, which it usually isn’t, and the engine is off, which under way it isn’t. Interestingly, this folk method is real physics: a wall with liquid behind it vibrates differently. Hold that thought.

Internal senders

Floats and probes give you a gauge at the helm — for the first season. Waste is the most hostile environment a sensor can live in, and these live in it. When they stick (not if), they fail confidently: the panel shows “half” while the tank fills to the vent.

External sensors — measure through the wall

Two technologies read the level with nothing inside the tank. Radar (Gobius C) sees through plastic and GRP walls and reports a continuous 0–100 %. Vibration (Gobius Pro) is the instrumented version of the knock test — it works on any wall material including stainless and aluminium, one level point per sensor. Both mount in about 15 minutes on the tank you already have.

The setup that works

  1. 01

    Early warning at 75 %

    One Gobius Pro sensor at three-quarter height — or an app alarm at 75 % on Gobius C. This is your “plan the pump-out” signal, days ahead of trouble.

  2. 02

    Hard alarm at 95 %

    Second alarm near full. With Gobius Pro’s relay output, light a lamp at the helm or sound a buzzer — unmissable even with guests aboard.

  3. 03

    Levels where you look

    App on the phone for the crew, from either sensor. With Gobius C, also NMEA 2000 to the chartplotter and Victron GX for the helm.

The rules, briefly

In Sweden (since 2015) and across much of the Baltic, discharging toilet waste from leisure boats is prohibited — pump-out stations are the only legal route for most coastal sailing. Equivalent no-discharge zones exist in many US and EU waters. A working level readout isn’t bureaucracy; it’s how you arrive at the station before the tank decides for you.

Total cost of ending the guessing

A single-point warning: one Gobius Pro sensor. The full picture: Gobius C on a plastic tank with both alarms configured in the app. Either way: no drilling, no maintenance, and the knock test retires with honour.

Questions

Holding-tank measurement — asked & answered

How full should I let the holding tank get?

Plan the pump-out at 75 % — that leaves margin for a weekend where the station is closed or occupied. Treat 95 % as an emergency alarm, not a plan.

Can I just keep a log instead of a sensor?

You can try — count heads, flushes and days. In practice guests, rinse water and holding-tank chemicals make the log drift within a week. A sensor costs less than one ruined cushion set.

Where on the tank should sensors sit?

For a single-point setup: at 75 % of tank height on a flat outer wall (Gobius Pro). For continuous readout: on top of the tank with clear view to the bottom (Gobius C, plastic/GRP tanks). Avoid internal baffles — the manual shows how to spot them.

What about the smell people associate with tank sensors?

That smell comes from through-fittings and their gaskets, not from measurement itself. External sensors add no fittings — the tank keeps exactly the openings it was built with.

Retire the screwdriver

An afternoon’s install ends years of guessing.